|Posted by Drip Fed Waste Oil Heating on March 30, 2018 at 3:20 AM||comments (0)|
We have a Haagon from Wanaka who is wanting waste oil, should you have any that you want to get rid of, please contact him at
Haagon East TRIBE Team Training;
Name : Haagon
Email Address : firstname.lastname@example.org
Message : Hi,
I have a waste oil burner in Wanaka, New Zealand - it is becoming increasingly difficult to access waste oil. Do you know if there is the possibility of it be...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on February 3, 2017 at 3:05 PM||comments (0)|
Shipment of fans have arrived today 4th Feb
|Posted by Drip Fed Waste Oil Heating on February 3, 2017 at 3:00 PM||comments (0)|
OK we have found the old blog cool.
|Posted by Drip Fed Waste Oil Heating on August 28, 2016 at 6:50 PM||comments (0)|
*We are currently working on water temperature controllers, for the fan forced spa pool heaters & pool heaters, which cut the fire right down to a glow, when in a spa pool, 38c has been reached, by cutting the oil flow. So now the oil flow can be managed via a small pump and controller.
This will save the spa pool owners approximately $50.00 in power a week, and beable to heat your spar pool for next to nothing, enabling you to actually use your spa pool once again.
So clean t...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on August 18, 2016 at 6:20 PM||comments (0)|
Currently building for customers
1 x Marshall heater, replacing a diesel burner for our waste oil burner, kit.
We have another 18kg heater in stock to be fitted with copper coil etc to heat water for a calf rearing farm.
And another 18 kg heater to heat inside a house.
Also i have a mate that wants one for free so have built it getting sandblasted and going to test a new blower setup today.
More cylinders arriving next week, so just let us get over th...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on August 10, 2016 at 5:35 AM||comments (0)|
After buying $200.00 dollars worth of fans and adapters, a mate came around last night with a more powerful fan. This morning I ran the heater for four hours and at burnt clean.
For some slight reason all the computer fans we normally use all smoked and it was getting a little fustrating I tell you. So have ordered ten more of these fans. Yes the heater is going at 294c at the time of this image was taken.Read Full Post »
|Posted by Drip Fed Waste Oil Heating on August 8, 2016 at 3:30 AM||comments (0)|
Well today didn't go as planed, I brought 10 computer fans of a guy on trademe, which was good, but when I used them, the fire smoked.
Went to Jaycar today and purchad $200.00 worth of fans, and power adapters, they all made the heater smoke too. OK can't be the fans then. Did I change the burner head, No. Lifted the pot up closer to the burning tube still smoked not as much, Progress.
Went and checked the last video of the last heater couldn't work it out until i pulled the...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on August 7, 2016 at 12:50 AM||comments (0)|
After 3 days of strong winds , heavy downpours of rain, the waste oil heater has survived the challenge, however water has managed to get into my 44 gallon drum, which is annoying to say the least.
I filled a 20 litre container only to find the fire wouldn't go correctly for 1/2 the day. Spitting and sparking the old bacon cooking sound.
So all i did was tilt the 20 litre container back onto a piece of 4x2 lifing the outlet up, so any water falls to the back of the container, heat...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on August 1, 2016 at 5:55 AM||comments (0)|
Well after three trips to Gasworkz today, one new regulator we now have the Co2 connected to the mig.
The welder works really well, I changed today from a welder/grinder with the arc welder, to a mig welder, if your've still using a stick, it's time to splash out and get a mig welder. Remeber the Co2 bottle can cost more than your welder itself and I also brought a nice big red cylinder which lasts alot longers than a couple of weeks werlding as this fire extinguisher does.
Oh the...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on July 28, 2016 at 4:40 AM||comments (0)|
I have had trouble with the oil feed line, blocking at the needle valve or airlocks, so took the tubing off, and replaced with 12mm polybutylene that I had lying about in the garage, reduced it back down to the needle valve and have found it has fixed that little problem. I think we may supply this pipe or 12mm tubing with these heaters.
|Posted by Drip Fed Waste Oil Heating on July 14, 2016 at 9:35 PM||comments (0)|
|Posted by Drip Fed Waste Oil Heating on July 14, 2016 at 9:30 PM||comments (0)|
|Posted by Drip Fed Waste Oil Heating on July 13, 2016 at 4:35 AM||comments (0)|
Well heater left for Rotorua today, so am now ready for another heater to build. Put your orders in now.
Currently have a mobility scooter to repair which is taking longer than first thought however all fun & games.
|Posted by Drip Fed Waste Oil Heating on July 5, 2016 at 8:00 AM||comments (0)|
I have just spent this morning checking the waste oil heater and the storage tank. Why? Just last night I notice the heat at the radiator drop to 42c quite quickly, when it had been going at around 55c most of the night, so I popped downstairs to the heater that's outside, only to find it had almost gone out, and a small pool of oil was starting to form inside the pot. That's not the normal operation of this heater, so turned it off and left it for this morning.
The oil flow had slowed...Read Full Post »
|Posted by Drip Fed Waste Oil Heating on June 29, 2016 at 6:00 AM||comments (0)|
The new Cebora 175 mig welder is on it's way here. Yes
Built a Frost Defender today got a little bit more to complete to finish it tomorrow.
The 45 kg heater is waiting now for the mig to arrive. Just got the fan to fit and paint, an it can be instock ready for when you call.
|Posted by Drip Fed Waste Oil Heating on June 27, 2016 at 6:05 AM||comments (0)|
Started building a 45 kg heater today, have the flue housing welded on, and the door open ready to hinge and open.
Airflow all built, ready to be fitted. Fan housing built. Almost done.
|Posted by Drip Fed Waste Oil Heating on June 23, 2016 at 1:40 AM||comments (0)|
Got the 2 x 18 kg heaters finished this avo. Now ready for your order.
|Posted by Drip Fed Waste Oil Heating on June 20, 2016 at 8:40 AM||comments (0)|
Working on the 2 x 18 kg heaters today, copper coil made and being fitted. Waiting on the steel truck to deliver steel pipe and box steel.
|Posted by Drip Fed Waste Oil Heating on June 19, 2016 at 12:50 AM||comments (0)|
Had the heater going all day today, it's been beautiful and warm inside , the radiator has been running at 63 degrees most of that time.
The whole upstairs is toastie.
Text from the latest heater instal in Dannievirke ; We had the the heater cranked up last night, maybe too much, very nice and hot inside the shed.
That's Great to hear.
|Posted by Drip Fed Waste Oil Heating on June 17, 2016 at 2:55 AM||comments (0)|
Delivered an 18 kg heater to Dannievirke today. We got it installed flue and flashed, going well inside a workshop. Toastie Warm.